This chapter contains an overview of the three main tools used in building live systems: live-build, live-boot and live-config.
live-build is a collection of scripts to build live systems. These scripts are also referred to as “commands”.
The idea behind live-build is to be a framework that uses a configuration directory to completely automate and customize all aspects of building a Live image.
Many concepts are similar to those used to build Debian packages with debhelper:
● The scripts have a central location for configuring their operation. In debhelper, this is the debian/ subdirectory of a package tree. For example, dh_install will look, among others, for a file called debian/install to determine which files should exist in a particular binary package. In much the same way, live-build stores its configuration entirely under a config/ subdirectory.
● The scripts are independent - that is to say, it is always safe to run each command.
Unlike debhelper, live-build provides the tools to generate a skeleton configuration directory. This could be considered to be similar to tools such as dh-make. For more information about these tools, read on, since the remainder of this section discuses the four most important commands. Note that the preceding lb is a generic wrapper for live-build commands.
● lb config: Responsible for initializing a Live system configuration directory. See The lb config command for more information.
● lb build: Responsible for starting a Live system build. See The lb build command for more information.
● lb clean: Responsible for removing parts of a Live system build. See The lb clean command for more information.
As discussed in live-build, the scripts that make up live-build read their configuration with the source command from a single directory named config/. As constructing this directory by hand would be time-consuming and error-prone, the lb config command can be used to create the initial skeleton configuration tree.
Issuing lb config without any arguments creates the config/ subdirectory which is populated with some default settings in configuration files, and two skeleton trees named auto/ and local/.
$ lb config [2015-01-06 19:25:58] lb config P: Creating config tree for a debian/stretch/i386 system P: Symlinking hooks...
Using lb config without any arguments would be suitable for users who need a very basic image, or who intend to provide a more complete configuration via auto/config later (see Managing a configuration for details).
Normally, you will want to specify some options. For example, to specify which package manager to use while building the image:
$ lb config --apt aptitude
It is possible to specify many options, such as:
$ lb config --binary-images netboot --bootappend-live "boot=live components hostname=live-host username=live-user" ...
A full list of options is available in the lb_config man page.
The lb build command reads in your configuration from the config/ directory. It then runs the lower level commands needed to build your Live system.
It is the job of the lb clean command to remove various parts of a build so subsequent builds can start from a clean state. By default, chroot, binary and source stages are cleaned, but the cache is left intact. Also, individual stages can be cleaned. For example, if you have made changes that only affect the binary stage, use lb clean --binary prior to building a new binary. If your changes invalidate the bootstrap and/or package caches, e.g. changes to --mode, --architecture, or --bootstrap, you must use lb clean --purge. See the lb_clean man page for a full list of options.
live-boot is a collection of scripts providing hooks for the initramfs-tools, used to generate an initramfs capable of booting live systems, such as those created by live-build. This includes the live system ISOs, netboot tarballs, and USB stick images.
At boot time it will look for read-only media containing a /live/ directory where a root filesystem (often a compressed filesystem image like squashfs) is stored. If found, it will create a writable environment, using aufs, for Debian like systems to boot from.
More information on initial ramfs in Debian can be found in the Debian Linux Kernel Handbook at http://kernel-handbook.alioth.debian.org/ in the chapter on initramfs.
live-config consists of the scripts that run at boot time after live-boot to configure the live system automatically. It handles such tasks as setting the hostname, locales and timezone, creating the live user, inhibiting cron jobs and performing autologin of the live user.
License: This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program. If not, see http://www.gnu.org/licenses/.
The complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL-3 file.
SiSU Spine (object numbering & object search) 2022